adams car整车装配通讯器问题
我的assembly打开后提示信息如下有好多通讯器没匹配上啊
Opening the assembly: 'aa'...
Opening the front suspension subsystem: 'front_susp'...
Opening the front steering subsystem: 'steering'...
Opening the front wheel subsystem: 'front_tires'...
Opening the rear wheel subsystem: 'rear_tires'...
Opening the body subsystem: 'body'...
Opening the brake_system subsystem: 'brakes'...
Opening the rear suspension subsystem: 'rear_susp'...
Assembling subsystems...
Assigning communicators...
WARNING: The following input communicators were not assigned during assembly:
testrig.cis_engine_rpm
testrig.cis_engine_speed
testrig.cis_max_gears
testrig.cis_diff_ratio
testrig.cis_max_throttle
testrig.cis_downforce_coefficient
testrig.cis_crankshaft_ratio
testrig.cis_transmission_efficiency
testrig.cis_drive_torque_bias_front
testrig.cis_max_engine_speed
testrig.cis_engine_revlimit_rpm
testrig.cis_min_engine_speed
testrig.cis_engine_idle_rpm
testrig.cis_transmission_spline
testrig.cis_engine_map
testrig.cis_transmission_input_omega
testrig.cis_clutch_displacement_ic
testrig.cis_max_engine_driving_torque
testrig.cis_max_engine_braking_torque
front_susp.cil_swing_to_body (attached to ground)
front_susp.cir_swing_to_body (attached to ground)
rear_susp.cil_tripot_to_differential (attached to ground)
rear_susp.cir_tripot_to_differential (attached to ground)
Assignment of communicators completed.
Assembly of subsystems completed.
Full vehicle assembly ready. 我的模型是错误的不能进行仿真
下面是软件自带模型打开后的消息
为什么我的有那么多不匹配 的通讯器呢
我每个子系统也没有少啊
Opening the assembly: 'MDI_Demo_Vehicle'...
Opening the front suspension subsystem: 'TR_Front_Suspension'...
Opening the rear suspension subsystem: 'TR_Rear_Suspension'...
Opening the front steering subsystem: 'TR_Steering'...
Opening the front wheel subsystem: 'TR_Front_Tires'...
Opening the rear wheel subsystem: 'TR_Rear_Tires'...
Opening the body subsystem: 'TR_Body'...
Opening the rear powertrain subsystem: 'TR_Powertrain'...
Opening the brake_system subsystem: 'TR_Brake_System'...
Assembling subsystems...
Assigning communicators...
WARNING: The following input communicators were not assigned during assembly:
testrig.cis_downforce_coefficient
testrig.cis_crankshaft_ratio
testrig.cis_transmission_efficiency
testrig.cis_drive_torque_bias_front
TR_Front_Suspension.cil_ARB_pickup
TR_Front_Suspension.cir_ARB_pickup
TR_Front_Suspension.cil_tripot_to_differential (attached to ground)
TR_Front_Suspension.cir_tripot_to_differential (attached to ground)
TR_Rear_Suspension.cil_ARB_pickup
TR_Rear_Suspension.cir_ARB_pickup
Assignment of communicators completed.
Assembly of subsystems completed.
Full vehicle assembly ready. 你再检查一下你建立的模板中通讯器的名称和角色是否与其他子系统相匹配 这也是我一直弄不参透的 请问楼主现在通讯器的问题解决了吗
页:
[1]